Yes, as long as you follow the steps above, but replace the steps for router 1 to router 2 and router 2 to router 3 and so on. Keep in mind the speeds will slow down with each router you add. It would be better if you could hook router 3 to router 1, but if the distance makes that an issue, the daisy chain is the way to go.

DSL Router with a hardwired connection once you have that working and can access the Internet, plug in the CAT 5 cable from the Modem/Router to the Uplink port of the Lynksis and then again with a If your Google Nest Wifi router or primary Google Wifi point and another nearby router are broadcasting the same Wi-Fi network name, it's possible that your personal device is connected to the other router's network. This can happen if you used an existing network name to set up your Google Nest Wifi or Google Wifi devices. If you use another router, then you have to do the configurations at the link. If you buy a MOCA bridge as suggested, then it's just plug and play and a lot easier to hook up. Pick your poison Adding a wireless router to an existing local area network adds a Wi-Fi access point to the network so you can share a single Internet connection. The wireless router and other network devices, such The Setup Router page will appear. Click Setup Router. The login page will appear. Type in the password: motorola and log in. You will then immediately get the page with the message that the router detected an IP address conflict between the LAN port and the WAN port. (see below) It will ask you if you want to avoid the conflict.

You can follow the same method to connecting two routers or more than 2 Wi-Fi router in the same network. Just pull the cable from the main internet router and connect the second router. Wired connection is the best way to connect two wifi router to share network devices with each other.

wirelessly no , but you could look at powerline adapters to connect main router to the orbi . however the orbi is designed to connect the main orbi router to the main router via ethernet and then the sat/s connect back to the orbi router via wifi which achieves the same thing Thank you for your reply information. I replied via the ATT community forum with a followup question - please check my reply there. My reply basically says that I found the Somejoe messages the other night, and it seem that his solution applies to my case.Basically, I should connect, via ethernet cable, between ATT router 3801 Home Network port jack (but NOT the broadband jack) and the new Deco can be used with an existing router. Here are two typical connection structures. Topology 1: Note: When Deco works in Router mode, it's not suggested to connect more than 1 deco unit to the existing router directly, as it may cause a network loop.. When Deco works in Access Point mode, it's no problem to connect more than 1 deco unit to the existing router directly. We show you how to Boost your Wifi signal by adding another wireless router and connecting the two using a cable.

You can easily extend your Wi-Fi network with additional networking hardware like Wi-Fi repeaters and Wireless Access Points. The other inexpensive option is that you get hold of an old wireless router, one that is longer in use, and connect it to your existing (main) router using an Ethernet (Cat5) cable. Use a Second Router as an Access Point

The Wi-Fi router range depends on the standard it supports. For example, Wireless N routers (802.11n) offer better range compared to Wireless-G routers. It is best to use two 802.11n routers, but a Wireless-G as the second router may work fine as well. Make sure you know the passkey and SSID for each router if you set up a wireless connection. When you set up a new router, place it near a Windows PC or another computer that can be used for the initial configuration. Both wired and wireless routers are best configured from a computer connected to the router with an Ethernet network cable. You can move the router to its permanent location later. How to Connect One Router to Another to Expand a Network Four Parts:Gather Your EquipmentSet Up Router 1Set Up Router 2Bring Your Network OnlineCommunity Q&A If you want to add more computers or other devices to your home or small business network By placing another router in the second house, and connecting the two to each other (either with ethernet or powerline, let's not go into that right now), you can extend your network. The second router provides extra sockets and WiFi in, but you have to set it up in "switch mode" (or bridge mode, in this context the difference is not important You can easily extend your Wi-Fi network with additional networking hardware like Wi-Fi repeaters and Wireless Access Points. The other inexpensive option is that you get hold of an old wireless router, one that is longer in use, and connect it to your existing (main) router using an Ethernet (Cat5) cable. Use a Second Router as an Access Point Step 2: Next, under the Virtual Interface section, you'll establish the settings you'll use to connect to this router. It's best to make these identical to the settings in the Physical Once you have the secondary router configured, you can place it where you want it to repeat the signal. In order to maintain a good connection, it should be placed in a location where it gets at least 50% signal strength from the primary router. Connect One Router to Another to Expand a Network.